They are making a number of good annotation on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in this content on the next paragraphs.
Installing a bathtub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably difficult job. If the old tub is readily easily accessible, the task can relocate rapidly; if you need to open up a wall surface to remove the old tub and position the new tub, the task is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need a helper to move out the old tub and set in the new one. Ensure you have qualified on your own for the task as well as are comfortable trying it. As opposed to working with a service provider to take control of a halfway-completed job, it is much better to think about employing one before you begin. Possibilities are you may require an expert plumber to make tube links.
This post will certainly assist you set up a new tub in your restroom if you have currently gotten a brand-new tub and don't require to alter the arrangement of your previous supply of water pipes.
Your devices and also product list ought to comprise the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you must do is detach the water supply. After doing so, activate the faucets to drain any kind of water staying in the system. The process of getting rid of the existing faucets can be quite bothersome because of the restricted accessibility that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipes. When the supply pipes have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before carrying on to fit the new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the current supply pipes.
If you need to fit a monobloc, after that you will need reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the faucet and the sink. Secure the tap in position with the supplier provided backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap connectors. The former type ought to be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Tub
Utilizing the two wooden boards under its feet, put the tub in the needed setting. The wood boards are practical in uniformly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 little factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bathtub till the level reviews degree.
To set up faucets, fit the bottom of the furthest flexible tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Switch on the water supply and examine all joints and also brand-new pipework for leaks and tighten them if necessary. Fill the bath tub as well as additionally examine the overflow electrical outlet as well as the typical outlet for leakages.
Ultimately, take care of the bath paneling as described in the manufacturer's user's manual. Tiling and also sealing around the bathtub ought to wait up until the tub has been used at least when as this will certainly resolve it into its final position.
Planning for the Installment
First of all, the supporting frame supplied with the bathroom needs to be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the faucet includes a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets device to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of both taps using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last position.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to split an inflexible seal, causing the water to pass through the wall surface between the bathroom and also the tiling, resulting in problems with wetness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, as well as can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Remember to always load the bathtub with water before securing, to permit the movement experienced when the tub remains in use. The sealant can break relatively very early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily available on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that blog post on How to Install a Bathtub when doing a lookup on the search engines. Sharing is good. Who knows, you could be helping someone out. I praise you for your time. Visit us again soon.
Click